Resources

Case Studies
Case Study
High-Density Internal Pitting Corrosion - EVO UMp+ Service

A pipeline operator with known high-density internal pitting corrosion located at the bottom of a 6" condensate water pipeline, required a high-resolution inline inspection.

Case Study
Crack Diagnosis in Blended Natural Gas - EVO Eclipse UCx Service

A North American pipeline operator contracted NDT Global to inspect an 18" Natural Gas Liquid (NGL) pipeline for cracks, including hook cracks.

Case Study
Post Construction Caliper Survey - ART Scan Series

A gas pipeline operator in Europe required a post-construction caliper inspection on a newly built pipeline.

Case Study
Detailed Ultrasonic Crack Inspection Achieved

In 2019 a Canadian pipeline operator approached NDT Global to better understand the integrity of two 12" pipeline segments totaling 290 km (180 miles) within their natural gas system.

Case Study
Next Generation ILI Crack Inspection Service - Phased Array Ultrasonic Solution

As ILI is the most efficient pipeline integrity management tool, an operator published a request for proposal (RFP) to develop and provide a solution that delivered a step-change in crack inline inspection (ILI) performance for challenging seam-weld geometries.

Case Study
Bi-Directional High-Resolution Inspection of a Subsea Flexible Riser Pipeline

The aim of this inspection was to assess the conditions and obtain reliable data of the critical parts of this pipeline section.

Case Study
Expedited Reporting of a Hydrogen Service Pipeline

The aim of this inspection was to validate previous ILI inspections and provide enhanced accuracy of the true condition of this pipeline.

Case Study
Long-Seam Pipeline Crack Inspection in Liquid Propane

After careful evaluation of its options for inspecting the 61.78 mile line, the operator chose NDT Global’s Evo Series 1.0 ultrasonic crack inspection tool.

Case Study
Simultaneous Crack and Metal Loss Inspection

A combination of high-resolution technologies were used to successfully detect metal loss and crack-like features in one run.

Case Study
Verifying Emerging Pipeline Cracking Threats Using Ultrasonic Technology

NDT Global utilized a 12" inspection tool which has inspected more than 2,600 km (1,616 miles) in a circumferential configuration.

Case Study
The Most Precise Pinhole and Pitting Services

Following the initial dig verification program, NDT Global worked alongside the operator to create a new set of requirements focusing on the accurate sizing of pittings and pinholes.

Case Study
Complex Crack Detection

An NDT Global field verification expert worked closely with the crew and conducted phased array UT to enhance the understanding of the crack geometries and provided crack depths.

Case Study
An Alternative to Hydrostatic Testing for Complex Cracking

To address tilted (hooked) and skewed cracks, a modified sensor arrangement was introduced to the fleet of tools.

Case Study
Evaluation of Cracks in a Petroleum Pipeline

Engineers from NDT Global carried out extensive investigations to gain visibility into overall pipeline integrity.

Case Study
Girth Weld Cracking Threats in a CRA-Cladded Gas Pipeline

To inspect a 16" gas pipeline, we prepared a project plan to facilitate the inspection which included pipeline preparation, inspection run and a re-establishment procedure.

Case Study
Custom-Engineered Offshore Solution for BP

After a review of requirements an advanced ultrasonic tool was selected to accurately measure wall thickness and metal loss.

Case Study
Inspecting a Dual-Diameter Pipeline in a Single Run

Both the pipeline operator and inspection engineers worked hand in hand to design, build, and test a multi-diameter ultrasonic tool to fulfill these specific requirements.

Case Study
Custom Engineered Baseline ILI for Multi-Diameter Export Route

We worked with an operator to launch an intensive development program focusing specifically on safe passage, while maximizing measurement accuracy.

Case Study
Delivering Precision by Combining FEA's with ILI's

SONACOL worked with NDT Global to perform an FEA, a method that is optimized to provide operators with an accurate estimation of pressure behaviors.

Case Study
Equinor: Custom Solution for an Extreme Subsea Pipeline

NDT Global performed the inspection run using high-resolution pinhole and pitting ultrasonic metal loss inspection technology.

Case Study
Ultrasonic Inline Inspection for Ethanol Pipelines

Following further investigations, to successfully begin the ILI process, NDT Global’s team proposed an ultrasonic wall thickness measurement inspection.